A robot is generally capable of repeating the same move towards a specific point in space, over and over, within a high level of tolerance (referred to as ‘unidirectional Repeatability’), generally well below 0.1mm. But this does not mean that that particular point in space is well known relative some global coordinate frame (such as the robot base frame): the level of ‘Absolute Accuracy’ achieved by an ‘off-the-shelf’ industrial robot is generally in the several millimeters and more. This is generally due to manufacturing tolerances for every robot unit, incorrect joint zero-mastering, mechanical flexibility, gear backlash, etc.
That problem is further compounded by the additional components forming the complete robot-cell. The end-effector attached at the end of the robot might have its own mechanical flexibility; furthermore, its actual built – and therefore its ‘point of interest’ (e.g. the tip of a drill) – probably differs from the design intent. The same holds true for the fixture located on the floor intended to hold the part. The situation gets even worse when involving one or more external axes along which the robot travels, and/or if the part is held on a one- or multi-axis positioner.
To achieve the highest possible Absolute Accuracy for a given robotic operation, it is therefore imperative to ‘close’ as much as possible the entire ‘metrological chain’ formed by the different components linking the point of interest on the robot’s end-effector (the TCP), on one end, and the point on the part the robot is operating on, on the other end. Sometimes, the just described general process is somewhat inversed, where the robot holds the part through a ‘gripper’ and the tool (TCP) is fixed on the floor.
The DynaCal™ robot calibration system allows not only robot calibration but the entire robot-cell calibration in one single step: the robot, the end-effector’s TCP, the fixture’s location (alignment), and optionally the external axes and/or positioner are calibrated altogether. This is achieved by moving the robot to a variety of positions in space, each time measuring the robot at (or at a point in a known location relative to) the TCP, expressed in the part’s coordinate frame. This can be performed with the DynaCal proprietary measurement hardware, or with any external (large-range) measurement equipment (such as a laser tracker).
Full Absolute Accuracy robot calibration as just described is used in virtually every kind of robotic application (except for very low-accuracy applications, such as painting), e.g. in arc-welding, waterjet cutting, drilling and routing, assembly, spot-welding, gauging, etc. The purpose of robot calibration is generally to reduce manual programming time, improve process quality, and/or to enable standard robots to achieve accuracies of much more expensive equipment (i.e. CNC machines, CMMs, etc.). Robot calibration enables ‘Off-Line Programming’, ‘Cloning’ of existing robot-cells, ‘Mirroring’ across production lines, ‘Swapping’ of robots, etc. (see “Off-Line Programming with No Touchup”, “Duplicate Robot Programs with No Touchup”).
Robot calibration, including calibration of its peripherals, for Absolute Accuracy with the DynaCal system is generally done once at the installation of the robot-cell, but it can of course be repeated at any time throughout production, for reasons such as robot maintenance, robot replacement, etc. However, during normal production operation, it is generally recommended to use a dedicated in-line recovery tool instead – such as the AutoCal™ or the AccuBeam™ system – in order to automatically detect and correct as promptly as possible any accuracy issue within the robot-cell, thus insuring that your robot-cell will maintain throughout production the level of Absolute Accuracy achieved at installation with the DynaCal robot calibration system (see “Maintain your Robot’s Accuracy throughout Production”).
Quick answers to questions you may have about our services. Can’t find what you’re looking for? Contact Us Now.
Dynalog does not publish or share public pricing. There is no public MSRP or standard price list. Pricing is available only through a custom quote based on your project requirements.
Temperature compensation in robotics refers to techniques used to counteract thermal-induced errors in industrial robots, ensuring consistent positioning accuracy despite temperature fluctuations. The ambient temperature changes and the robot self-heating can induce the thermal related errors in the robot. Dynalog’s AccuBeam and DynaFlex products provide the ability to compensate robot for thermal-induced errors.
Robot guidance is the accurate identification of the part location with respect to robot. This feature is required when the part is not located repeatedly in the same location with respect to the robot.
Robotic inspection system is used to measure parts to identify the part dimensions and features are within tolerance. It includes an off the shelf industrial robot with a 3D sensor mounted to the robot end-effector. Dynalog’s DynaFlex system provides the high Absolute Accuracy and Accuracy Over-time required of such systems.
The roPOD system recalibrates the Tool Center Point (TCP) X, Y, Z, and Orientation. In addition, it can also recalibrate the zero-position mastering of the robot.
Yes, the roPOD system has a feature called “QuickCheck” that based on a couple of measurements of the end-effector can identify any change in the Tool Center Point.
We are committed to exceeding client expectations by delivering innovative, sustainable, and cost-effective construction solutions.
6001 North Adams Road,
Bloomfield Hills, MI 48304, USA
We collect cookies to analyze our website traffic and performance; we never collect any personal data.
