Absolute Accuracy Robot Calibration

A robot is generally capable of repeating the same move towards a specific point in space, over and over, within a high level of tolerance (referred to as ‘unidirectional Repeatability’), generally well below 0.1mm. But this does not mean that that particular point in space is well known relative some global coordinate frame (such as the robot base frame): the level of ‘Absolute Accuracy’ achieved by an ‘off-the-shelf’ industrial robot is generally in the several millimeters and more. This is generally due to manufacturing tolerances for every robot unit, incorrect joint zero-mastering, mechanical flexibility, gear backlash, etc.

That problem is further compounded by the additional components forming the complete robot-cell. The end-effector attached at the end of the robot might have its own mechanical flexibility; furthermore, its actual built – and therefore its ‘point of interest’ (e.g. the tip of a drill) – probably differs from the design intent. The same holds true for the fixture located on the floor intended to hold the part. The situation gets even worse when involving one or more external axes along which the robot travels, and/or if the part is held on a one- or multi-axis positioner.

To achieve the highest possible Absolute Accuracy for a given robotic operation, it is therefore imperative to ‘close’ as much as possible the entire ‘metrological chain’ formed by the different components linking the point of interest on the robot’s end-effector (the TCP), on one end, and the point on the part the robot is operating on, on the other end. Sometimes, the just described general process is somewhat inversed, where the robot holds the part through a ‘gripper’ and the tool (TCP) is fixed on the floor.

The DynaCal™ system allows calibration of your entire robot-cell in one single step: the robot, the end-effector’s TCP, the fixture’s location (alignment), and optionally the external axes and/or positioner are calibrated altogether. This is achieved by moving the robot to a variety of positions in space, each time measuring the robot at (or at a point in a known location relative to) the TCP, expressed in the part’s coordinate frame. This can be performed with the DynaCal proprietary measurement hardware, or with any external (large-range) measurement equipment (such as a laser tracker).

Full Absolute Accuracy robot-cell calibration as just described is used in virtually every kind of robotic application (except for very low-accuracy applications, such as painting), e.g. in arc-welding, waterjet cutting, drilling and routing, assembly, spot-welding, gauging, etc. The purpose of robot-cell calibration is generally to reduce manual programming time, improve process quality, and/or to enable standard robots to achieve accuracies of much more expensive equipment (i.e. CNC machines, CMMs, etc.). Robot-cell calibration enables ‘Off-Line Programming’, ‘Cloning’ of existing robot-cells, ‘Mirroring’ across production lines, ‘Swapping’ of robots, etc. (see “Off-Line Programming with No Touchup”, “Duplicate Robot Programs with No Touchup”).

Calibration for Absolute Accuracy with the DynaCal system is generally done once at the installation of the robot-cell, but it can of course be repeated at any time throughout production, for reasons such as robot maintenance, robot replacement, etc. However, during normal production operation, it is generally recommended to use a dedicated in-line recovery tool instead – such as the AutoCal™ or the AccuBeam™ system – in order to automatically detect and correct as promptly as possible any accuracy issue within the robot-cell, thus insuring that your robot-cell will maintain throughout production the level of Absolute Accuracy achieved at installation with the DynaCal system (see “Maintain your Robot’s Accuracy throughout Production”).

 

 

Home
Products
Applications
Case Studies
Services
About Us
Contact
<<Applications
dynalogmainsite001010.jpg
Recipient of the
Joseph F. Engelberger
Award for Technology
>Applications>Off-Line Programming with No Touchup
>Applications>Duplicate Robot Programs with No Touchup
>Applications>Maintain your Robot's Accuracy throughout Production
>Case Study>Integrated OLP process at JCI using DynaCal
>Case Study>No Manual touch up with DynaCal at Ford - Genk
>Case Study>Off-Line Programming Specification at PSA Peugeot Citroën
>Case Study>Dynalog Accuracy Tested at Renault
Automated In-Line Gauging About Us Applications Products About DynaCal DynaFlex CompuGauge AutoCal AccuBeam DynaGuide Robot Guidance for Part-to-Part Variation Absolute Accuracy Robot Calibration Off-line Programming with No Touchup Robot Performance Analysis Contact Us {Copyright (C) 2017 Dynalog, Inc. All Rights Reserved} dynalogmainsite001003.jpg dynalogmainsite001002.jpg Duplicate Robot Programs with No Touchup Maintain your Robot's Accuracy throughout Production Minimize Robot Downtime Accurate Cutting, Sealing, Welding with your Robot Adaptive Robot Control for Ultimate Accuracy Targeted Robot Communication Solutions Turn your Robot into Precision Machining Equipment
>Product>DynaCal